Edinson Borda Villcas. Test de Percepcion Visual Frostig Manual. Uploaded by. MARIA Abs Cambios Uploaded by. Patricio Patri. Manual Autorizacion Btp. Manual Autorizacion Btp. Uploaded by. Patricio Patri · PROBMON1-Ser Omni 6- 25 Min (Problemas). Uploaded by. Patricio Patri · Test Psi Co Tec Nico. Manual Autorizacion Btp Descripción: PROGRAMACIONES BTP INFORMÁTICA HONDURAS M Topographie 2-Approfondissement BTP- TSGT.
|Published (Last):||10 November 2012|
|PDF File Size:||3.13 Mb|
|ePub File Size:||19.87 Mb|
|Price:||Free* [*Free Regsitration Required]|
Rotate motor shaft further two revolutions in same direction. Then gently fit the encoder in position ensuring that slot fits properly on the pin. Tighten bolts 15 with a light force.
Faults and corrective actions. Simultaneously it is necessary to ensure that the teeth of drive gear 73 and drum cam gear 8 mesh with orientation marks properly aligned.
Pragati – BTP Turret Manual – PDF Free Download
Fit the partial spindle assembly into the main body 45 with the help of bolts 2 and cyl. Proper clamped position is indicated by lighted LED on proximity switch This BTP achieved a passenger confidence rating of There are 2 valve positions on the coolant ring.
Suggested flow chart is given in the diagram on page Hold sliding coupling 4 by one hand to prevent its rotation, and rotate drum cam gear 8 by hand fig. It is preferable to allow the turret to slip in the event of an accidental shock or overload. Unusual knocking sound during indexing is also an indication of mechanical problem.
Operation of coolant system. Denel Turret Lct30 Full description. If in doubt connect 24V DC supply to the turret.
Rent E Books Manual Autorización Btp Epub | Website for downloading cbse books!
They also give excellent protection against damage by hot chips. In the clamped position of the turret, bolts 15 are in line with the holes drilled in flange In case turret clamping is not possible then rotate the motor shaft in whichever direction possible; in some intermediate position bolts 15 will be in line with the holes in flange Typical circuit diagram is given in page 9.
Assemble all the components 70, 71, 76 to 84 as shown in fig. Hand cranking is required for inspecting the setting of encoder and proximity switch.
Bolts should be tightened in diagonal order, and in 3 or 4 stages. Btp italia salvo62barbato Education. Use extraction screws and pull out the end plate In such a case, tool position number, and encoder feedback will not match. Check axial clearance of drum cam by a dial indicator as shown in figure by lifting and lowering the cam gear by hand.
Replace with a new button, and place back the spring and the plug. Fit these subassemblies in the main body 45without loosing their general orientation. Details of Electrical Connections 1 4 2 3 1.
Faults and corrective actions: Fitment of tool disc on manuak turret. Coolant valve button Coolant valve 1 Even if turret clamping is not possible at this stage follow the next steps.
Pragati – BTP Turret Manual
The drum cam pulls the sliding coupling into engagement atorizacion applies clamping force through disc spring. Three piece face gear coupling is the basic element used for indexing. Control should be capable of detecting the proximity switch signal within 3 to 6 ms.
Laporan btp pdf Documents. Machine surface should be either scraped or surface-ground. If the turret does not function properly immediately after an accident, internal component damage can be suspected. It is therefore, not possible to adjust the angular position of coolant ring by hand. Strategic overview of British Transport Police in Scotland Crank the motor autorizacoin bring the turret in clamped position, as indicated by proximity switch LED.
A drain plug has been provided to drain out the oil, if so required. Assemble the components 70, 71, 73, 74, 75 as shown in fig 6. Declamped position can be sensed by the reduction in pressure during hand cranking. Turret has two alternative positions for the connection of coolant pipe. Remaining components of the cam shaft are to be assembled at auorizacion later autoizacion.
Tighten opposite bolts in sequence 1,5,2,6,3,7,4,8. Requirements of turret control: In such accidents, the friction joint of Ringfeder slips; and protects the internal mechanism from damage.